Acrylic sheet will soften if it reaches temperatures of over 80°C, so it is very important to take measures to keep the temperature at a minimum when machining or manipulating the acrylic. Water and water/air mists, compressed air and soluble oils are all suitable for use as coolants, however take care to ensure oils do not contain solvents as these may damage the acrylic.

If the scratches are light, we stock Xerapol acrylic scratch remover polish which is ideal for use on all of our cut acrylic. A small amount will buff out imperfections in the surface of your acrylic sheet leaving you with a shine again. Larger and deeper scratches may be sanded out with a very fine sandpaper and buffed with a high quality polish, but we recommend that caution is taken. Please contact us should you need any advice with the maintenance of your acrylic sheet.

Acrylic is very simple to care for if you take care with it. All that is needed is a soft cloth, warm water and a small amount of washing up liquid. The soap doesn’t just clean the sheet, it will act as a lubricant to stop small amounts of dirt scratching the acrylic as you clean. You may wish to moisten the sheet with water before you begin to wipe with the cloth to soften and lift the dirt from the surface. Once you are satisfied it is clean, rinse off the detergent with cold water and leave to dry. Avoid using the following products: Window cleaners Methylated Spirits Kitchen scouring compounds Products containing ammonia Products containing ketones or halogens Aromatics and solvents including; thinners, acetone, gasoline, turpentine, white spirit, tetrachloride and benzene. Using any of the above is completely unnecessary and may damage the surface of the acrylic or make it cloudy. Additionally, scouring pads or other abrasive materials should never be used to clean your acrylic sheet.

Yes, however they have to be very well sealed. It is also worth considering the care that should be taken when cleaning acrylic.

3mm for smaller panels, but for larger (approx. 600mm+) panels 5mm should be used.

Plastic Machining West Midlands
Plastic Machining

2mm is the standard thickness that we advertise, however larger panels should go up to 3mm depending on how well they are supported in the frame.

Yes, acrylic is very strong and lightweight, making it perfect for use as secondary glazing. Acrylic of 3mm+ is ideal, but thickness should be increased for larger panels. Please contact us should you need any further advice.

Yes, colourless acrylic is a total white light transmittance of 92%, which is the highest possible of any material. It is as transparent as the finest optical glass.

The weather resistance of acrylic cannot be matched by any other transparent plastic material. Many years of outdoor exposure in a variety of applications have proved the excellent weather resistance of this material.

Acrylic sheeting achieves a UK Class 3 fire rating. Polycarbonate has a Class 1 fire rating which makes it highly recommended for use in schools and hospitals.

Yes, there are many options for gluing acrylic, but it largely depends on what material it is being affixed to. Acrylic cements come in a variety of types and thicknesses, thinner cements will offer seamless joining, but will not fill voids as thicker cements will. Superglue and similar adhesives may provoke a chemical reaction with acrylic that will damage your sheet, latex glues (e.g. Copydex) are a good choice, but your local builders’ merchant will be able to offer advice on which adhesive to use. Nevertheless please be sure to read and follow the material safety data manual before bonding.

Threading acrylic is possible but it is not recommended if frequent assembling/disassembling is likely. A sure way to prevent damage to your acrylic sheet when screwing to a surface is to use wall plugs and screws

Yes, use a metal drill bit on a medium speed and don’t apply too much pressure. Drilling too quickly may crack or damage the plastic due to the generation of heat. If possible, drilling from both sides of the sheet to break through it is recommended. Drilling acrylic is easy to do but please note the following points to avoid the pitfalls: Use a drilling rack if available Once a drilling depth of 5mm is reached cool the material with either water or an air blaster At deep drillings “air out” and drill several times. This is best after each 1mm drilling The correct cutting rate and feed is identified by a smooth and connected chip flow At the beginning and close to the puncture reduce the feed rate. For round saw cuts up to 60mm use a hole saw sometimes known as a “slugger” cutter pre-drill the centre with a suitable drill. If you would rather we drilled your acrylic for you, we are happy to do so at only a small cost.

For very thin acrylic sheets a scriber or blade may be used, in the same way you would cut glass. Draw the scriber several times across the sheet along a straight edge, then hold or clamp the sheet firmly, apply a downward pressure and snap the sheet along the seam. If your sheet is thicker, fine-toothed handsaws are recommended for smaller jobs, the acrylic should be securely clamped and only light pressure applied. Power saws with alternate bevelled teeth are suitable, especially band saws, jig saws and fret saws. Blades designed to cut aluminium or copper are appropriate for use with acrylic. Should you not wish to cut the sheeting yourself, we are happy to cut your plastic sheet at only a small cost. Acrylic sheet is easy to saw when the correct tools are employed please see below for tools that are adequate. Circular saw bench Circular hand saws with hard metal saw blades. Multiple toothing saw-blades with a tooth pitch of approximately 13mm. Always use well ground saw blades and allocate a saw for use only with acrylic. Jigsaws Fret Saws Bow Saws; since the saw blades are set there is no good cutting edge (outburst) is achievable. Therefore ensure the blade is sharp. The correct cutting condition can be used through the number of strokes and change of feeder. Carving or craft knives can be used with basic extruded acrylic to aid separation but not with Hi-Impact acrylic or PETG.

Cast Acrylic & Extruded Acrylic The key differences between these types of acrylic stem from the method used in manufacturing. Extruded acrylic is made by extruding acrylic polymer over long production runs, whereas cast acrylic is made by casting the acrylic resin into a mould. Therefore cast acrylic is less uniform in thickness than extruded acrylic, however it displays greater thermal stability and can be reworked hot. It also has better impact resistance than extruded acrylic, and is less prone to developing cracks when exposed to solvents. Extruded acrylic sheeting is a more economical option than cast acrylic, and has more advantages when it comes to vacuum forming making it a great general purpose sheeting. However it has limitations in its ability to be machined and fabricated. Extruded acrylic sheet has reduced mechanical properties, however it does give process advantages when heating, bending and vacuum forming, and has a better thickness tolerance than cast acrylic sheet. Extruded sheets are ideal for general glazing applications and the much lower viscosity when hot, makes it more ductile than Cast Acrylic. Cast Acrylic sheets offer greater thermal stability and better resistance to crazing when exposed to solvents. The thermoforming range for cast sheets is wider. They can be reworked hot, which is not always possible with extruded sheets. The surface finish, flatness and optical properties of Cast Acrylic are all superior to those of Extruded Acrylic sheets. Polycarbonate & PETG Polycarbonate is a very tough and versatile form of plastic sheeting, less easy to work and fabricate than acrylic, though superior in terms of impact resistance. PETG also has a high impact resistance, and is more economical than polycarbonate, although it has a lower superficial hardness. Polycarbonate is unmatched for high strength and resistance to pressure, however it is more susceptible to scratching. If you are unsure as to what type of plastic sheeting will suit your needs, please contact us and we will be happy to offer any advice you require.

Request a quote

Any enquiries please get in touch

Telephone – 01543 577888
Mobile – 07931 434611
07398 893056
E: sales@profileplusltd.co.uk

Profiles Plus Limited

Unit 14, Beechwood Business Park, Burdock Close, Cannock, Staffs, WS11 7GB

01543 577888

Hours of business

Mon: 8:00 am – 5:00 pm
Tue: 8:00 am – 5:00 pm
Wed: 8:00 am – 5:00 pm
Thu: 8:00 am – 5:00 pm
Fri: 8:00 am – 5:00 pm
Sat: By Appointment
Sun: Closed